Fixings & Metalwork

Hex Nyloc Nut with metric thread, for general use with bolts and threaded bar (studding).
The Nyloc insert prevents accidental loosening caused by vibration.
BZP (Bright Zinc Plate) finish.

Thread: 10mm - Metric
Depth: 10mm
Spanner Size: 17mm

A large heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.

Dimensions: 3mm x 40mm x 40mm
11mm Bolt Hole: To suit M10 thread

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Hex head coach screw, for heavy-duty applications. Suitable for fixing into timber, can fix into brickwork and masonry with an M10 plug. M10 washers sold separately.

- Length excludes 7mm bolt head
- 85mm screw thread, 15mm unthreaded
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 6 - 8mm pilot hole
- Hex Head fits a 17mm Spanner

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 10mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 100mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 50mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Hex head coach screw, for heavy-duty applications. Suitable for fixing into timber, can fix into brickwork and masonry with an M10 plug. M10 washers sold separately.

- Length excludes 7mm bolt head
- 95mm screw thread, 35mm unthreaded
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 6 - 8mm pilot hole
- Hex Head fits a 17mm Spanner

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 130mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 80mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Hex head coach screw, for heavy-duty applications. Suitable for fixing into timber, can fix into brickwork and masonry with an M10 plug. M10 washers sold separately.

- Length excludes 7mm bolt head
- 105mm screw thread, 45mm unthreaded
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 6 - 8mm pilot hole
- Hex Head fits a 17mm Spanner

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 150mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 100mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 10mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Hex head coach screw, for heavy-duty applications. Suitable for fixing into timber, can fix into brickwork and masonry with an M10 plug. M10 washers sold separately.

- Length excludes 7mm bolt head
- 125mm screw thread, 55mm unthreaded
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 6 - 8mm pilot hole
- Hex Head fits a 17mm Spanner