Masonry Fixings

Brown plastic plugs, fix into concrete, brick and masonry by drilling a 7.0mm hole, suitable for use with woodscrews.

- Brown plugs are suitable for No.8 - No.12 (4.0mm - 6.0mm) screws
- Plug Length: 36mm
- Use a 7.0mm masonry drill bit

Red plastic plugs, fix into concrete, brick and masonry by drilling a 5.5mm hole, suitable for use with woodscrews.

- Red wall plugs are suitable for No.6 - No.10 (3.5mm - 5.0mm) screws.
- Plug Length: 30mm
- Use a 5.5mm masonry drill bit

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 5mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 8mm
Anchor Length - 75mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 35mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 8mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 8mm
Anchor Length - 100mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 60mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 8mm
Anchor Length - 130mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 90mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 75mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 25mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 10mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 100mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 50mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 130mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 80mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 150mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 100mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 10mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm