Fixings & Metalwork

30mm Galvanised Staple - 1kg Bag (Approx. 260)

Cut point staples, typically used for attaching wire and netting to timber.

Staple length: 30mm
Staple gauge: 3.55mm
Average staple count = 260 /kg
Finish: Galvanised, service class 3

Stock Availability: 11 in stock

From £7.49 Inc. VAT

40mm Galvanised Staple - 1kg Bag (Approx. 136)

Cut point staples, typically used for attaching wire and netting to timber.

Staple length: 40mm
Staple gauge: 4.0mm
Average staple count = 136 /kg
Finish: Galvanised, service class 3

Stock Availability: 13 in stock

From £7.99 Inc. VAT

30mm Sherardised Twisted Nail - 1kg

Square twisted nails; the recommended fixing for installation of joist hangers.

Nail length: 30mm
Nail gauge: 3.75mm
Average nail count = 350 /kg
Finish: Sherardised, service class 2

Stock Availability: 17 in stock

From £7.39 Inc. VAT

25mm Sherardised Panel Pins - ½kg Bag

Light-duty nails /pins suited to fixing small decorative components; timber to timber. Small head for flush finish.

Pin length: 25mm
Pin gauge: 1.6mm
Average pin count = 2340 /kg (½ kg bag)
Finish: Sherardised, service class 2
Manufactured to BS EN 10230-1

Stock Availability: 8 in stock

From £7.73 Inc. VAT

40mm Sherardised Panel Pins - ½kg

Light-duty nails /pins suited to fixing small decorative components; timber to timber. Small head for flush finish.

Pin length: 40mm
Pin gauge: 1.6mm
Average pin count = 1590 /kg (½ kg bag)
Finish: Sherardised, service class 2
Manufactured to BS EN 10230-1

Stock Availability: 12 in stock

From £7.75 Inc. VAT

13mm Galvanised Felt Clout Nails - 500g (Approx. 345)

Short galvanised nails with an extra large clout head, designed for fixing down shed felt.
Approximately 345 nails per 500g pack.

Stock Availability: 25 in stock

From £3.97 Inc. VAT

M8 x 75mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 8mm
Anchor Length - 75mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 35mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm

Stock Availability: 380 in stock

From £0.82 Inc. VAT

M8 x 100mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 8mm
Anchor Length - 100mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 60mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm

Stock Availability: 396 in stock

From £0.94 Inc. VAT

M8 x 130mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 8mm
Anchor Length - 130mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 90mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm

Stock Availability: 211 in stock

From £1.18 Inc. VAT

M10 x 75mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 75mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 25mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

Stock Availability: 192 in stock

From £1.03 Inc. VAT

M10 x 100mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 100mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 50mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

Stock Availability: 241 in stock

From £1.32 Inc. VAT

M10 x 130mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 130mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 80mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

Stock Availability: 133 in stock

From £1.80 Inc. VAT

M10 x 150mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 10mm
Anchor Length - 150mm
Washer Size - 12mm (M12)
Min Hole Depth - 70mm
Min Over Drill Depth - 20mm
Min. Embed Depth - 50mm
Max. Fixture Thickness - 100mm
Drill Bit Dia. for clearance - 12mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 17mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 60Nm

Stock Availability: 142 in stock

From £1.99 Inc. VAT

M12 x 150mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 12mm
Anchor Length - 150mm
Washer Size - 14mm (M14)
Min Hole Depth - 85mm
Min Over Drill Depth - 25mm
Min. Embed Depth - 60mm
Max. Fixture Thickness - 90mm
Drill Bit Dia. for clearance - 14mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 19mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 80Nm

Stock Availability: 88 in stock

From £3.20 Inc. VAT

M12 x 200mm Masonry Bolt

A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.

Drill Bit Dia. - 12mm
Anchor Length - 200mm
Washer Size - 14mm (M14)
Min Hole Depth - 85mm
Min Over Drill Depth - 25mm
Min. Embed Depth - 60mm
Max. Fixture Thickness - 140mm
Drill Bit Dia. for clearance - 14mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 19mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 80Nm

Stock Availability: 93 in stock

From £4.25 Inc. VAT

7.5 x 62mm Masonry Screw

A self-tapping Masonry Screw for brick and concrete, a popular fixing to fit window frames. An easy to use fixing that does not require plastic plugs, it has a high resistance to fire compared to nylon fixings. This screw is a friction fixing which minimises expansion stress in the base material, this allows fixing near to the edge, and gives greater loading performance than most nylon fixings.
To use: pre-drill a 6mm pilot hole, use a drill or impact driver fitted with T30 bit to drive the screw in.

T30 bit and white cover caps included when bought in box quantities of 100.

Drill Bit Dia. - 6mm
Min. Embed Depth - 45mm
Head Type - T30 Torx
Driver Type - Drill / Impact Driver

Stock Availability: 369 in stock

From £0.13 Inc. VAT

7.5 x 82mm Masonry Screw

A self-tapping Masonry Screw for brick and concrete, a popular fixing to fit window frames. An easy to use fixing that does not require plastic plugs, it has a high resistance to fire compared to nylon fixings. This screw is a friction fixing which minimises expansion stress in the base material, this allows fixing near to the edge, and gives greater loading performance than most nylon fixings.
To use: pre-drill a 6mm pilot hole, use a drill or impact driver fitted with T30 bit to drive the screw in.

T30 bit and white cover caps included when bought in box quantities of 100.

Drill Bit Dia. - 6mm
Min. Embed Depth - 45mm
Head Type - T30 Torx
Driver Type - Drill / Impact Driver

Stock Availability: 372 in stock

From £0.16 Inc. VAT

7.5 x 102mm Masonry Screw

A self-tapping Masonry Screw for brick and concrete, a popular fixing to fit window frames. An easy to use fixing that does not require plastic plugs, it has a high resistance to fire compared to nylon fixings. This screw is a friction fixing which minimises expansion stress in the base material, this allows fixing near to the edge, and gives greater loading performance than most nylon fixings.
To use: pre-drill a 6mm pilot hole, use a drill or impact driver fitted with T30 bit to drive the screw in.

T30 bit and white cover caps included when bought in box quantities of 100.

Drill Bit Dia. - 6mm
Min. Embed Depth - 45mm
Head Type - T30 Torx
Driver Type - Drill / Impact Driver

Stock Availability: 635 in stock

From £0.19 Inc. VAT

7.5 x 122mm Masonry Screw

A self-tapping Masonry Screw for brick and concrete, a popular fixing to fit window frames. An easy to use fixing that does not require plastic plugs, it has a high resistance to fire compared to nylon fixings. This screw is a friction fixing which minimises expansion stress in the base material, this allows fixing near to the edge, and gives greater loading performance than most nylon fixings.
To use: pre-drill a 6mm pilot hole, use a drill or impact driver fitted with T30 bit to drive the screw in.

T30 bit and white cover caps included when bought in box quantities of 100.

Drill Bit Dia. - 6mm
Min. Embed Depth - 45mm
Head Type - T30 Torx
Driver Type - Drill / Impact Driver

Stock Availability: 440 in stock

From £0.23 Inc. VAT

7.5 x 152mm Masonry Screw

A self-tapping Masonry Screw for brick and concrete, a popular fixing to fit window frames. An easy to use fixing that does not require plastic plugs, it has a high resistance to fire compared to nylon fixings. This screw is a friction fixing which minimises expansion stress in the base material, this allows fixing near to the edge, and gives greater loading performance than most nylon fixings.
To use: pre-drill a 6mm pilot hole, use a drill or impact driver fitted with T30 bit to drive the screw in.

T30 bit and white cover caps included when bought in box quantities of 100.

Drill Bit Dia. - 6mm
Min. Embed Depth - 45mm
Head Type - T30 Torx
Driver Type - Drill / Impact Driver

Stock Availability: 439 in stock

From £0.30 Inc. VAT

7.5 x 182mm Masonry Screw

A self-tapping Masonry Screw for brick and concrete, a popular fixing to fit window frames. An easy to use fixing that does not require plastic plugs, it has a high resistance to fire compared to nylon fixings. This screw is a friction fixing which minimises expansion stress in the base material, this allows fixing near to the edge, and gives greater loading performance than most nylon fixings.
To use: pre-drill a 6mm pilot hole, use a drill or impact driver fitted with T30 bit to drive the screw in.

T30 bit and white cover caps included when bought in box quantities of 100.

Drill Bit Dia. - 6mm
Min. Embed Depth - 45mm
Head Type - T30 Torx
Driver Type - Drill / Impact Driver

Stock Availability: 376 in stock

From £0.37 Inc. VAT

M5 x 50mm Hammer Fixing

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 5mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Stock Availability: 31 in stock

From £0.07 Inc. VAT

M6 x 60mm Hammer Fixing

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Stock Availability: 144 in stock

From £0.12 Inc. VAT

M6 x 80mm Hammer Fixing

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Stock Availability: 167 in stock

From £0.18 Inc. VAT

M8 x 100mm Hammer Fixing

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 8mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Stock Availability: 139 in stock

From £0.24 Inc. VAT

M10 x 100mm Hammer Fixing

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 10mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Stock Availability: 130 in stock

From £0.36 Inc. VAT

M10 x 160mm Hammer Fixing

A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.

Installation:
Pre-drill a 10mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.

Minimum fixing depth: 45mm

Stock Availability: 112 in stock

From £0.72 Inc. VAT

Red Wall Plugs - Box of 100

Red plastic plugs, fix into concrete, brick and masonry by drilling a 5.5mm hole, suitable for use with woodscrews.

- Red wall plugs are suitable for No.6 - No.10 (3.5mm - 5.0mm) screws.
- Plug Length: 30mm
- Use a 5.5mm masonry drill bit

Stock Availability: 4 in stock

£0.96 Inc. VAT

Brown Wall Plugs - Box of 100

Brown plastic plugs, fix into concrete, brick and masonry by drilling a 7.0mm hole, suitable for use with woodscrews.

- Brown plugs are suitable for No.8 - No.12 (4.0mm - 6.0mm) screws
- Plug Length: 36mm
- Use a 7.0mm masonry drill bit

Stock Availability: 7 in stock

£1.13 Inc. VAT

M6 x 65mm Carriage Bolt

Carriage Bolt; cup square hex, 16mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 148 in stock

From £0.14 Inc. VAT

M8 x 50mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 47 in stock

From £0.17 Inc. VAT

M8 x 75mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 143 in stock

From £0.22 Inc. VAT

M8 x 100mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 129 in stock

From £0.27 Inc. VAT

M8 x 130mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 120 in stock

From £0.34 Inc. VAT

M8 x 150mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 149 in stock

From £0.37 Inc. VAT

M8 x 180mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 290 in stock

From £0.61 Inc. VAT

M8 x 200mm Carriage Bolt

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 194 in stock

From £0.66 Inc. VAT

M10 x 75mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 70 in stock

From £0.36 Inc. VAT

M10 x 100mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 102 in stock

From £0.43 Inc. VAT

M10 x 130mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 149 in stock

From £0.51 Inc. VAT

M10 x 150mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 142 in stock

From £0.58 Inc. VAT

M10 x 180mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 210 in stock

From £0.74 Inc. VAT

M10 x 200mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 187 in stock

From £0.86 Inc. VAT

M10 x 230mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 135 in stock

From £1.10 Inc. VAT

M10 x 300mm Carriage Bolt

Carriage Bolt; cup square hex, 23mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 60 in stock

From £1.38 Inc. VAT

M12 x 50mm Carriage Bolt

Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 150 in stock

From £0.58 Inc. VAT

M12 x 100mm Carriage Bolt

Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 95 in stock

From £0.71 Inc. VAT

M12 x 130mm Carriage Bolt

Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 96 in stock

From £0.80 Inc. VAT

M12 x 150mm Carriage Bolt

Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 72 in stock

From £0.92 Inc. VAT

M12 x 180mm Carriage Bolt

Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Stock Availability: 75 in stock

From £1.12 Inc. VAT

Payment options