Fencing Materials

15 metre roll of twin-strand barbed wire. Suitable for DIY security. Produced from high quality mild steel wire, made in the U.K.

- 2.0mm Line Wires (x2)
- 1.8mm Barbing wire (standard twist, 4 barb)
- 15m Roll
- Galvanised

Galvanised steel barbed wire bracket, designed to be fitted to the front or back of a post. It has two 11mm diameter holes for fixings. This bracket securely supports up to three lines of of barbed wire. Welded construction.

Dimensions:
Fixing Plate: 4mm x 37mm x 380mm
Angled Arm: 4mm x 37mm x 445mm
Angle of Arm: 135°
The angled arm finishes 280mm higher than the top of the fixing plate

90mm Ferrule Winder is a wire strainer for tensioning fencing line wire.

Length - 90mm
Width - 50mm

Fix the winder to the side of a post or use an angle cleat to fix the winder to the face of a post. Feed your wire through the hole in the barrel and then turn the barrel with a spanner or socket. Tighten the locking nut to securely hold the wire in place.

Barrel Strainers are a specialist product used to strain fencing line wire.
8mm (thread diameter) X 110mm (barrel length).

To strain the wire: first wind the central barrel anti-clockwise until the hook and the eye are fully extended. Attached the hook of the strainer to an eye bolt (attached to a fence post), then attach the wire you want to strain to the eye of the barrel strainer. Wind the central barrel of the strainer clockwise to tension the wire. When complete, the strainer remains in situ and can be re -tightened if the wire loses tension.

Ratchet Wire Strainers are a specialist product for straining fencing line wire and barbed wire.

To strain the wire: attach the base of the strainer to a post using the fixing hole, feed your wire through the hole in the barrel of the strainer and then wind the barrel with a spanner. When the wire reaches your required tension, engage the ratchet catch to secure the wire in place. The wire can easily be re-tensioned when required.

30mm Fence Panel L-Clip, a useful panel clip for discreet fixing that can only be seen from one side. Can also be used to fix gravel boards, as well as many uses as a general purpose corner bracket.

- Angle: 30 x 30mm
- Height: 50mm
- Galvanised Steel

35mm Fence Panel Clips; used to attach fence panels to wooden posts. Minimum of 4 clips needed per fence panel.

- Fits fence panels up to 35mm thick
- Galvanised Steel

45mm Fence Panel Clips; used to attach fence panels to wooden posts. Minimum of 4 clips needed per fence panel.

- Fits fence panels up to 45mm thick
- Galvanised Steel

50mm Fence Panel Clips; used to attach fence panels to wooden posts. Minimum of 4 clips needed per fence panel.

- Fits fence panels up to 50mm thick
- Galvanised Steel

52mm Easy Fix Panel Clip for attaching fence panels to wooden posts. Easy Fix Panel Clips are first fitted to your fence panel and then secured to the post, eliminating the problem of lifting the panel high enough to slot into traditional 'U' shaped panel clips.

- Fits fence panels up to 47mm thick
- Minimum post width required - 80mm
- Brown Powder Coating

52mm Easy Fix Panel Clip for attaching fence panels to wooden posts. Easy Fix Panel Clips are first fitted to your fence panel and then secured to the post, eliminating the problem of lifting the panel high enough to slot into traditional 'U' shaped panel clips.

- Fits fence panels up to 52mm thick
- Minimum post width required - 85mm
- Brown Powder Coating

Galvanised steel bracket for attaching 75mm triangular Arris Rail to square posts or wall plates. Minimum post/wall plate width is 45mm.

Angle: 62 x 62mm (suits 75mm Arris Rail)
Wings: 42 x 155mm (overall width)
Length: 285mm
Fixing Holes: (10x) 5mm diameter + (2x) 27mm x 6mm slots

Galvanised Steel Knee Rail Strap with 90° bend; for fixing rails used with birdsmouth posts. These straps can be bent in situ to suit various sizes of knee rail fencing.

Dimensions: 0.8mm x 75mm x 500mm (250mm either side of bend)
Fixing Holes: (10x) 4.0mm

Galvanised Steel Flat Knee Rail Strap; used to fit knee rails in place (the rails used with birds mouth posts). These straps can be bent in situ to suit various sizes of knee rail fencing.

Dimensions: 0.8mm x 75mm x 500mm
Fixing Holes: (10x) 4.0mm

This post support is designed to hold a 75 x 75mm square wooden post in position when it’s not possible to concrete a post into the ground. The metal fins inside of the post support wedge into the timber ensuring a quick and secure fit.

- Designed to fit 75 x 75mm square wooden posts
- Fin-Grip post support system
- Bolt down plate: 150mm x 150mm
- Bolt holes: 4 x 12mm Ø holes for bolting down the base (approx. 115mm hole centres)
- Manufactured from 2mm thick steel
- Welded construction
- Galvanised finish for durability outdoors