Builders Metalwork

The RR ridge rafter connector provides alignment control and correct nailing locations. The RR47 may be used with any rafter slope up to 30°. Galvanised for corrosion resistance.

For back-to-back installations, the minimum width of the ridge plate is 38mm. Secure in place using 3.75 x 30mm square twisted nails.

Measurements (Ref. image 3):
A: 47mm
B: 83mm
C: 33mm
D: 114mm
t (Thickness): 1.2mm

Fixing Holes:
Header: 4mm (x4)
Joist: 4mm (x4)

Nationwide delivery is available on this product, call 0117 967 4382 for details or submit a contact form below.

Galvanised mini joist hanger for constructing timber to timber framework. Precision formed and engineered for fast installation and maximum loads.

- Suitable for hanging 47mm wide timber
- Width - 115mm (including fixing wings)
- Length - 62mm
- Depth - 48mm

Install using 3.75 x 30mm square twist nails:
16 nail holes / hanger
1 kg square twist nails installs 21 hangers

Simpson Strong-Tie NP15/80/140 nail plates can be used in various applications, in particular for jointing or the connection of wood elements in the same plane.

Thickness: 1.5mm
Width: 40mm
Length: 120mm
Fixing Holes: 5.0mm (x9)

30mm Fence Panel L-Clip, a useful panel clip for discreet fixing that can only be seen from one side. Can also be used to fix gravel boards, as well as many uses as a general purpose corner bracket.

- Angle: 30 x 30mm
- Height: 50mm
- Galvanised Steel

Galvanised fixing band FB20A has many building & DIY uses.

- Flexible galvanised steel can be easily shaped by hand
- 1mm thick
- 20mm Wide
- 10m Coil
- Includes three hole options to suit a variety of fixings

Galvanised joist hanger for constructing timber to timber framework. Precision formed and engineered for fast installation and maximum loads.

- Suitable for 150mm wide timber
- Width - 287mm (including fixing wings)
- Height - 440mm
- Depth - 55mm

A mild steel plate with fixing holes used for strengthening and repairs.
Pre-drilled for use with countersunk screws. Bright Zinc Plated (BZP) for corrosion resistance.

Thickness: 2.5mm
Width: 26mm
Length: 150mm
Fixing Holes: 5.0mm (x4)

Metal brace for strengthening corners. Can be used for internal or external corners.
Pre-drilled for use with countersunk screws, countersunk on both sides of fixing hole.
Bright Zinc Plated (BZP) for corrosion resistance.

Thickness: 2.5mm
Width: 24mm
Length: 150mm x 150mm
Drill Holes: 7.0mm (x6)

The HES (heavy engineered strap) replaces traditional heavy restraint straps in roof and floor construction. Reducing the thickness to 1.5mm allows the HES strap to span over the top of floor joists and the bottom chords of trusses without the need for notching.

Complient with BS EN 845-1, Simpson Strongtie heavy engineered restraint straps are less than 40% of the weight, quicker to fit and overcome many fixing problems associated with traditional heavy straps.

The HES (heavy engineered strap) replaces traditional heavy restraint straps in roof and floor construction. Reducing the thickness to 1.5mm allows the HES strap to span over the top of floor joists and the bottom chords of trusses without the need for notching.

Complient with BS EN 845-1, Simpson Strongtie heavy engineered restraint straps are less than 40% of the weight, quicker to fit and overcome many fixing problems associated with traditional heavy straps.

A post support fitting for installing timber posts and timber framework. The timber sits on the Post Support out of ground contact, which prevents rotting due to moisture from the ground. The height/level of the square support plate can easily be adjusted which is useful when building structures on uneven ground. Suitable for structurally supported timber posts and framework that need to last a long time e.g. for a basic timber porch or decking framework. Not recommended for free standing posts e.g. fence posts.

Installation: drill a 22mm diameter hole in the end of the timber post for the threaded bar to fit into, the depth of hole will vary depending on how much elevation is required. The post should sit firmly over the threaded bar down to the square support plate. The two nuts are tightened against each other to lock the support plate in the required position. The bottom of the post support is designed to be bolted down to a concrete base, we recommend using M10 Thunder Bolts.

- Welded construction, galvanised steel
- Total Height - 255mm
- Threaded bar - 22mm diameter
- Square support plate - 100 x 100mm x 4.5mm
- Bolt Down Plate - 100 x 100mm x 4.5mm
- 11mm fixing holes (x8)

Steel T-plate suitable for a range of timber frame building uses. Bright Zinc Plated (BZP) for corrosion resistance.

Thickness: 2.0mm
Overall Width: 100mm x 19mm
Overall Length: 100mm x 19mm
Fixing Holes: 6.0mm (x5)

A mild steel plate with fixing holes used for strengthening and repairs.
Pre-drilled fixing holes for use with countersunk screws. Bright Zinc Plated (BZP) for corrosion resistance.

Thickness: 2.0mm
Width: 19mm
Length: 100mm
Fixing Holes: 5.0mm (x4)

Metal corner plate for strengthening corners. Pre-drilled fixing holes for use with countersunk screws.
Bright Zinc Plated (BZP) for corrosion resistance.

Thickness: 2.0mm
Width: 16mm
Length: 100mm x 100mm
Fixing Holes: 6.0mm (x6)

Metal brace for strengthening corners. Can be used for internal or external corners.
Pre-drilled for use with countersunk screws, countersunk on both sides of fixing hole.
Bright Zinc Plated (BZP) for corrosion resistance.

Thickness: 2.0mm
Width: 24mm
Length: 100mm x 100mm
Drill Holes: 6.0mm (x6)

For vertical and horizontal restraint when connecting timber floor and roof systems to masonry walls.

Pre-galvanised twisted restraint straps, designed to building regulations for vertical restraint.

Strap thickness: 2mm
Strap width: 28mm
Strap total length: 1000mm
Distance from top of strap to top of twist: 100mm
6mm holes along the length of the strap

For vertical and horizontal restraint when connecting timber floor and roof systems to masonry walls.

The HES (heavy engineered strap) replaces traditional heavy restraint straps in roof and floor construction. Reducing the thickness to 1.5mm allows the HES strap to span over the top of floor joists and the bottom chords of trusses without the need for notching.

Complient with BS EN 845-1, Simpson Strongtie heavy engineered restraint straps are less than 40% of the weight, quicker to fit and overcome many fixing problems associated with traditional heavy straps.